XH-W1209 Digital Display Temperature Controller

 XH-W1209 Digital Display Temperature Controller

Description :
XH-W1209 Thermostat Temperature Control Module , Water Heat Control 


XH-W1209 Thermostat Temperature Control Module , Water Heat Control 


XH-W1209 Thermostat Temperature Control Module , Water Heat Control 

 

  1. Resolution: 0.1°C(-9.9~99.9°C), 1°C(Other Ranges)
  2. Accuracy: 0.1°C
  3. Refresh Rate: 0.5s
  4. High Temperature Protection: 0~110°C
  5. Measurement Input: NTC(10K 0.5%) Waterproof Type Sensor
  6. Output Range: 1 Channel 10A Relay Output
  7. Humidity: 20%-85%
  8. Environment: -10~60°C,  

Connect the power supply and the load, then you can supply to the controller.

It displays the measured temperature, press SET key, the display temperature flashing, press"+" "-" to set the desired temperature. After finished, press SET to confirm and back.Now the controller automatically performs the relay by setting off. This temperature controller output is 10A relay, meeting various high-power loads, please make sure the wires are connected correctly.

 Indicator, LED State Instruction:

Indicator: OFF indicates the relay is switched off; ALWAYS indicates the relay is closed.

LED: shows LL means the sensor opens; shows HH means it's out of range, the thermostat will be forced to close the relay, the display --- as high temperature protection

Functions and settings of the thermostat

At the beginning it is good to introduce thermostat control for easy work. The XH-W1209 has three control buttons on the SET, + and -.If you press the SET button for 2 seconds enters the menu with seven options for setting the thermostat (P0,P1,P2,P3,P4,P5,P6).

Here is basic schematic for temperture controller XH-W1209

schematic diagram XH-W1209

In the temperature controller XH-W1209 menu will move with buttons + and – to select the value or raising or lowering the temperature.

The red LED display indicates when the relay is activated.Always shines as long as the relay is activated.If the relay is switched off LED off.

PO  Heating or Cooling ?

Here we set the temeperature controller operation mode C- cooling , H-heating.

If you set Cooling (C) temperature controller will be activated relay when temperature falls to the setpoint.

If you set Heating (H) temperature controller will be activated relay when temperature raise to setpoint.

OLYMPUS DIGITAL CAMERA

P1 – Hysteresis or Return diference set

This device model can value set by 0.1C and the lowest value is 0.1C.This is a very useful feature for precise operation of the temperature controller.For example, if you set the value of 1C  and the desired temperature on the thermostat 20C relay will be deactivated at 21C (20C+1C). The relay is activated again when the temperature drops to 20C.

OLYMPUS DIGITAL CAMERA

 

P2 – Highest temperature limit

You can set a maximum temperature limit, less than 110 degrees.

OLYMPUS DIGITAL CAMERA

 

P3 – Lowest temperature limit

You can set minimum  temperature limit more as 50 degrees.

OLYMPUS DIGITAL CAMERA

P4- Temperature correct or calibration

Very good feature that lets you set your thermostat by certified accurate thermometer.

If you do not have a certified thermometer leave the value at 0C. Calibration allows you to adjust the temperature in 0.1 increments.

OLYMPUS DIGITAL CAMERA

P5-Delay starting time

In this step, you set the start delay in minutes 1-10 min.If you set 1min relay is activated until one minute after reaching the set temperature.P5 code delay starting time

P6-High temperature Alarm

The menu P6 initially turns OFF to ON and press the SET,then set the temperature at which the alarm is activated. When is alarm activated display not showing temperature only – - -.

 

OLYMPUS DIGITAL CAMERA

Write a review

Please login or register to review
  • Views: 3670
  • Brand: Tiah
  • Product Code: DZD001951
  • Availability: 40
  • 1,100.00DA
  • Ex Tax: 1,100.00DA

Tags: xh, w1209, digital, display, temperature, controller